登車橋如何操作
？

2022-11-16 16:13:18

1686次

登車橋給我們的生活帶來了極大的便利，登車橋主要由搭板

、面板

、底架、安全擋板

、支撐腳

、升板油缸、搭板油缸

、電控箱

、液壓站等組成。那么大家應該如何正確操作登車橋呢

？
1

、登車橋 http://www.8kvv.com/在操作時首先要壓動升柄，使登車橋上升

，至高于車廂底板

，然后車輛到位，松開回油閥

，登車橋下降并使唇板平穩地搭接到車輛尾部,用鏈子把登車橋和車固定牢

。
Ramps at the operating pressure of the first to move up the handle, make Ramps rise above the cabin floor, and then the vehicle in place, release the oil return valve, Ramps and lip steadily declined by hooking the rear of the vehicle, Ramps and with a chain to the car fixed firmly.
　
2、登車橋操作時合上電控箱內電源總開關

，按下操作按鈕

，固定式登車橋面板慢慢上升，升到最大高度時

，登車橋前端搭板開始伸出

，當搭板升到與面板同一平面時，松開按鈕

，面板與搭板在同一平面內慢慢下降

，搭板會自然地搭在汽車尾部車廂底面上。
Ramps close when operating a power control box power switch, press the action button, fixed Ramps panel slowly rose, rose to a maximum height, Ramps slab stretched out the front, when slab liter to the same plane with the panel, release the button, the panel and slab slowly declining in the same plane, slab naturally carriage ride in the rear of the car on the bottom surface.

3、登車橋 http://www.8kvv.com/如果車廂底面低于安裝登車橋的月臺高度

，在松開按鈕使面板下降的同時

，拉緊小鏈條使支撐腳偏離支撐腳墊缺口，面板和搭板就可以下降到低于月臺高度處

，直至搭板落到較低的車廂內底面上

。
If the car underside Ramps Ramps installed below the height of the platform, release the button in the panel declined, while the supporting foot chain taut little deviation notch support pads,panels and slab can drop below at the height of the platform until the slab fell on the bottom surface of the lower compartment.

4、登車橋工作完畢后

，按下操作按鈕

，面板與搭板一起上升，車開走

，松開按鈕

，面板自動下落歸位，最后切斷電源總開關

。
Ramps After work is completed, press the action button, the panel raised with the slab, the car drove off, release the button, the panel automatically return the whereabouts of the last off the power switch.

上一篇：升降貨梯主要配件包括哪些

？

下一篇：固定式升降機