升降舞臺如何做好平行度控制設計
？

2022-11-16 16:13:18

1569次

升降舞臺隨滑塊在滑道中移動而升降，設計要求滑塊移動距離相同時

，兩組平臺升降距離相同

，因此在設計時要做好平行度控制。

、由于設計要求升降舞臺http://www.8kvv.com/90個單元閉合高度為恒定值

，因而設計工裝共4件

，放在大平臺的四個角

，大平臺放在工裝上后就能夠保證大平臺在同一高度。很多情況下，上軸承座和大平臺有間隙

，此時調整油缸活塞桿

，使某一軸承座和大平臺之間無間隙，如有間隙時墊入合適厚度鋼板

，軸承座和大平臺焊接牢固

。
Due to the design requirements for the lifting stage 90 units closed height is a constant value, thus a total of four tooling design, on the four corners, a large platform on a large platform after tooling to ensure a large platform at the same height. In many cases, the bearing and a large platform with a gap, then adjust the cylinder piston rod, so that no gap between the bearing and a large platform, pad into the appropriate thickness steel plate if clearances,bearing housings and a large platform welding firm.

、上滑道安裝是確保升降舞臺在升降過程中滿足大平臺平行度的關鍵

，根據機構設計原理，上

、下軸承座和下滑道固定的情況下

，如果上、下滑道不平行

，厚鋼板點處上滑道和大平臺有間隙

。
The slide installation is key to ensuring a large platform parallelism landing stage to meet the lifting process, according to mechanism design theory, on the case of a fixed bearing and glideslope, if on the glide path is not parallel,the thick steel plate at the point slides and a large platform with a gap.

3、升降舞臺http://www.8kvv.com/用行車吊在大平臺重心點

，平穩升至最大凈升高度

，測量大平臺4個角的高度

，確保4個角升高距離在允差范圍內

，此時上滑道和大平臺間隙墊入合適厚度鋼板，上滑道和大平臺焊接牢固

。
Landing stage hung a large platform with a driving focus point, steady rise to a maximum net lifting height, height measuring large platform four corners, four corners to ensure increased distance is within the tolerance range, this

time on a slide and a large gap between the pad into a suitable platform the thickness of the steel, the slide and a large platform welding firm.

上一篇：升降舞臺有哪些明顯的特點

？

下一篇：固定式升降平臺